|
|
Two of my old furniture clamps.
Date: 07/17/2009
Views: 197
|
|
My old clamps along side of one of the new ones
Date: 07/17/2009
Views: 151
|
|
The is a picture of the tail end of the clamp
Date: 07/17/2009
Views: 131
|
|
|
Another shot showing it tilted down for adjusting
Date: 06/27/2009
Views: 122
|
|
The beginning of the head end of the clamp.
Date: 06/27/2009
Views: 118
|
|
Another view of the head end. Note the head only has a cleanance hole.
Date: 06/27/2009
Views: 127
|
|
|
Another shot of the head showing it glued with a 1/2" dowel through.
Date: 07/08/2009
Views: 131
|
|
I made 17 clamps in all and had my table full!
Date: 07/09/2009
Views: 130
|
|
Another shot of my table with all the clamps
Date: 07/09/2009
Views: 119
|
|
|
This is showing the slide block on the head with the screw
Date: 07/17/2009
Views: 131
|
|
The wood screw. I used a thread box to turn the threads.
Date: 07/17/2009
Views: 138
|
|
Another view of the head assembly.
Date: 07/17/2009
Views: 146
|
|
|
The head assembly extended. The block in the middle is tapped.
Date: 07/17/2009
Views: 103
|
|
Another view
Date: 07/17/2009
Views: 128
|
|
The wide board will be replaced with a block glued to the slide block.
Date: 07/17/2009
Views: 99
|
|
|
Slide block, screw and screw end piece.
Date: 07/17/2009
Views: 110
|
|
19
Date: 07/17/2009
Views: 107
|
|
20
Date: 07/17/2009
Views: 131
|
|
|
21
Date: 07/17/2009
Views: 125
|
|
22
Date: 07/17/2009
Views: 112
|
|
This is the beginning of making the screw lever.
Date: 07/17/2009
Views: 104
|
|
|
I'm turning this to a 3/4" round ball
Date: 07/17/2009
Views: 105
|
|
25
Date: 07/17/2009
Views: 118
|
|
26
Date: 07/17/2009
Views: 129
|
|
|
Starting to take shape
Date: 07/17/2009
Views: 109
|
|
28
Date: 07/17/2009
Views: 123
|
|
Parting it off
Date: 07/17/2009
Views: 122
|
|
|
30
Date: 07/17/2009
Views: 138
|
|
O clamped a block on my drill press table and drilled an 11/16" hole in it.
Date: 07/17/2009
Views: 115
|
|
That helps align the ball while drilling
Date: 07/17/2009
Views: 99
|
|
|
33
Date: 07/17/2009
Views: 107
|
|
!/2" hole in ball about 1/2 way through
Date: 07/17/2009
Views: 95
|
|
1/2" dowel with two balls assembled
Date: 07/17/2009
Views: 127
|
|
|
Sanded, glued and installed on the screw.
Date: 07/17/2009
Views: 127
|
|
38
Date: 07/17/2009
Views: 132
|
|
This is what I'm using for a clamping table. The 1" deep grooves will hold the clamps
Date: 07/01/2010
Views: 119
|
|
|
6 Clamps sitting in the holders.
Date: 07/01/2010
Views: 159
|
|
A glue up!
Date: 07/01/2010
Views: 138
|
|
42
Date: 07/01/2010
Views: 119
|
|
|
43
Date: 07/01/2010
Views: 107
|
|
I made an "L" so I could clamp the holders to my table.
Date: 07/01/2010
Views: 89
|
|
45
Date: 07/01/2010
Views: 94
|
|
|
Last but not least, my rack holds 17 clamps and the two guide bars
Date: 07/01/2010
Views: 231
|
|
|
